Project:******* (CompleteStandstill)-Updated: MAY 3rd, pg9-
36161 views
139 replies
36 following
K
Project:******* (CompleteStandstill)-Updated: MAY 3rd, pg9-
kdcgrohl
+1y
Well I got her done for Lay'd Out at the Park last weekend. long, cold ass trip, but worth it. good show, very nice stuff there(see show coverage in pic forum). anyway, i'll take some more pics soon. i'm going to take the axle out this week or next to break it down for powder since i just painted it for the show.
i'm kinda proud of it tho, got best frame @ Lay'd out 07. bad thing is now i'm outa $ so motor will have to wait a couple months.
i'm kinda proud of it tho, got best frame @ Lay'd out 07. bad thing is now i'm outa $ so motor will have to wait a couple months.
northerntoy
+1y
amazing work you guys put on frames
kdcgrohl
+1y
Well, hope you guys feel like reading...
So I FINALLY got my axle back together so I decided it was picture time. And since my chassis/suspension is now DONE, heres the big list of mods:
Ceramic coated, drilled and slotted rotors from LC Engineering.
Highgloss silver powdercoated frame and tranny xmember.
Semigloss black powdercoated assload of bolts/nuts/washers, gas tank, airtanks, axle tube, gear housing, backing plates, drums, calipers, arms, link bars.
Chrome pike nuts on the rearend housing, chrome acorns on the shocks.
Stainless buttonheads and a few stainless hex bolts everywhere i could put em. All the rest of the fasteners are powdercoated black.
Stainless hardlines and fittings, braided stainless flex lines.
Center section of frame was replaced with 2x3x.25 box tubing, driveshaft xmember is 2x2x.25 tubing. exhaust cutouts are also 2x2.x25. tranny crossmember is Cando cut for exhaust.
The only painted items are the steering box/linkage and the fuel pump/sender.
New goodies from toyota include all six bodymounts, hole plugs in frame, exhaust hangers, wheelbearing and seals, plugs in backingplates, and axle housing gasket.
guess thats enough rambling, on with the pics...
Motor/trans is next!
So I FINALLY got my axle back together so I decided it was picture time. And since my chassis/suspension is now DONE, heres the big list of mods:
Ceramic coated, drilled and slotted rotors from LC Engineering.
Highgloss silver powdercoated frame and tranny xmember.
Semigloss black powdercoated assload of bolts/nuts/washers, gas tank, airtanks, axle tube, gear housing, backing plates, drums, calipers, arms, link bars.
Chrome pike nuts on the rearend housing, chrome acorns on the shocks.
Stainless buttonheads and a few stainless hex bolts everywhere i could put em. All the rest of the fasteners are powdercoated black.
Stainless hardlines and fittings, braided stainless flex lines.
Center section of frame was replaced with 2x3x.25 box tubing, driveshaft xmember is 2x2x.25 tubing. exhaust cutouts are also 2x2.x25. tranny crossmember is Cando cut for exhaust.
The only painted items are the steering box/linkage and the fuel pump/sender.
New goodies from toyota include all six bodymounts, hole plugs in frame, exhaust hangers, wheelbearing and seals, plugs in backingplates, and axle housing gasket.
guess thats enough rambling, on with the pics...
Motor/trans is next!
twisted minis
+1y
That looks awesome.
lotoy86
+1y
damn son lookin good
whynotfab
+1y
very nice work, i just looked through all of the pics
twisted minis
+1y
Whoah, Ricky is back! Fix your signature buddy.
vegasyota94
+1y
shit looks good man..
wtf ricky, where u been man
wtf ricky, where u been man
kdcgrohl
+1y
got it this far along for freakshow7, here's some pics somebody else took, i'll get around to a real update in a few days.
no1lowr
+1y
you might wanna rethink that gas tank, very nice roller otherwise.