K
Custom Tacoma Spindles!!!
draggintoy
+1y
hmm wonder how i never seen that part in your reply... I must be working too much.
onehightoyota
+1y
max, PM me when they start rollin off the assembly line. badass03taco@aol.com or on here. thanx. oh a question, since they're 3inch drop spindles, what about the steering link? will the steering knuckle be in the same location or dropped as well? as you know with 20's and 22's on a taco, the steering rack has to be moved up to take a little angle out of the steering linkage. can you move the entire steering knuckle down about two inches for those who dont wanna section their oil pan and move theri steering rack up? i moved mine up and i'll attest to it. its not that hard but definitely takes time. just relocating the mount on the spindle an inch or two lower would help on steering link angle
dragnbody
+1y
I wanna set too.
sittin_so_low
+1y
Edited: 11/30/2006 6:45:54 PM by madmax95
double posted....
double posted....
sittin_so_low
+1y
count me in. any deadline or time line when you might get these done by chance? thanks
BioMax
+1y
Originally posted by badass03taco
max, PM me when they start rollin off the assembly line. badass03taco@aol.com or on here. thanx. oh a question, since they're 3inch drop spindles, what about the steering link? will the steering knuckle be in the same location or dropped as well? as you know with 20's and 22's on a taco, the steering rack has to be moved up to take a little angle out of the steering linkage. can you move the entire steering knuckle down about two inches for those who dont wanna section their oil pan and move theri steering rack up? i moved mine up and i'll attest to it. its not that hard but definitely takes time. just relocating the mount on the spindle an inch or two lower would help on steering link angle
That's kina the point of a dropped spindle, not to put too much angle on the parts. The steering arm is on the ball joint, so me moving it around isn't a concern. I have been asked this a few times. It won't be a concern, they will just bolt on and lay a short 22" or I won't build them.
I am hoping to have set (or more) done by Reso.
max, PM me when they start rollin off the assembly line. badass03taco@aol.com or on here. thanx. oh a question, since they're 3inch drop spindles, what about the steering link? will the steering knuckle be in the same location or dropped as well? as you know with 20's and 22's on a taco, the steering rack has to be moved up to take a little angle out of the steering linkage. can you move the entire steering knuckle down about two inches for those who dont wanna section their oil pan and move theri steering rack up? i moved mine up and i'll attest to it. its not that hard but definitely takes time. just relocating the mount on the spindle an inch or two lower would help on steering link angle
That's kina the point of a dropped spindle, not to put too much angle on the parts. The steering arm is on the ball joint, so me moving it around isn't a concern. I have been asked this a few times. It won't be a concern, they will just bolt on and lay a short 22" or I won't build them.
I am hoping to have set (or more) done by Reso.
durangedkustoms
+1y
I'll be interested in a set for an 05 taco if your going to make them. I'll probably just talk to u at reso.
sideshizzle
+1y
Any news on these? I'm interested in getting a set.
BioMax
+1y
Were are building the first set right now. It's important that they do what we all need them too. It looks like there should be no problems getting them to lay a 22 while getting 12" of lift. Hopefully I can post a pic of the finished spindle next week.
truck action
+1y
Found this ,might help,Barely Legal Fabrication.