K
Lowest vehicle
Blzer2BNoticdNJ
+1y
my blazer is BD 4 1/2 with a 4 inch chop top. it sits about 45inches high (i think) i haven't measured it ina while. i ahve mo pics yet though.
time1
+1y
My buddy dannys yota...it sits 43 1/2 inches tall with a traditional BD. I think hes planning on a chop top....
nvrloenuf
+1y
Mine sits at 42in on the nose. 2in chop, 2in section and about 1/2in off the door in a 95 hardbody.. Still looks proportional too.. Thats that cool part..
What size rim and tire are ya'll running? I don't think I will be running anything bigger then 17's..
What size rim and tire are ya'll running? I don't think I will be running anything bigger then 17's..
no1lowr
+1y
Originally posted by TiMe_1
My buddy dannys yota...it sits 43 1/2 inches tall with a traditional BD. I think hes planning on a chop top....weird how the blue yota and the one hacked past the door are the same height, somebody cant measure.
My buddy dannys yota...it sits 43 1/2 inches tall with a traditional BD. I think hes planning on a chop top....weird how the blue yota and the one hacked past the door are the same height, somebody cant measure.
impounded dakota
+1y
Originally posted by NO1LOWR
Originally posted by TiMe_1
My buddy dannys yota...it sits 43 1/2 inches tall with a traditional BD. I think hes planning on a chop top....weird how the blue yota and the one hacked past the door are the same height, somebody cant measure.
Matt cut 1 1/2" out of his door, i messaged him to see exactly what hieght he is, but he is lower than that black traditionally bd'd yota.
Originally posted by TiMe_1
My buddy dannys yota...it sits 43 1/2 inches tall with a traditional BD. I think hes planning on a chop top....weird how the blue yota and the one hacked past the door are the same height, somebody cant measure.
Matt cut 1 1/2" out of his door, i messaged him to see exactly what hieght he is, but he is lower than that black traditionally bd'd yota.
fkntukn1
+1y
well my car will ber right around 36 inches tall when its done unibody dropped roadster chop.
FuktUup
+1y
my yota is 43 1/4. If danny's yota is the same height as mine with a traditional I would really like to see a picture of that 8+inch cliff.
pure insanity
+1y
Originally posted by NO1LOWR
Originally posted by pure insanity custom
Edited: 9/15/2005 11:16:27 PM by pure insanity custom
what do you get when you trim the bottom of the frame and do a 5.5" b.d. ? something like this. im not near it right now but im sure its roof is less than 40 inches tall. the fender directly above the tire is like 25" high.
my toys fender is 20.5 inches tall so i dont see how thats 25
well, im not standing near the truck to measure it but heres how i got the 25" measurement. im running a 15" wheel with a 195/50/15 tire. that tire overall measures something like 23" when the truck is all the way laid out it tucks over half the wheel and all thats left of the inner fenders is just a flat piece of sheet metal that is what connects the core support to the cab. the tire touches that piece of metal laid out. now i know the inside lip of the fender(where it bolts down) is about 1"-1 1/4" tall. so i figure i can call that 25" the bottom of the fenders is chopped along with the rockers, and lower bed sides. truck only needed about 3.5" to lay the rockers, i took off another 2" to go deeper. why lay rockers when you can lay door.
Originally posted by pure insanity custom
Edited: 9/15/2005 11:16:27 PM by pure insanity custom
what do you get when you trim the bottom of the frame and do a 5.5" b.d. ? something like this. im not near it right now but im sure its roof is less than 40 inches tall. the fender directly above the tire is like 25" high.
my toys fender is 20.5 inches tall so i dont see how thats 25
well, im not standing near the truck to measure it but heres how i got the 25" measurement. im running a 15" wheel with a 195/50/15 tire. that tire overall measures something like 23" when the truck is all the way laid out it tucks over half the wheel and all thats left of the inner fenders is just a flat piece of sheet metal that is what connects the core support to the cab. the tire touches that piece of metal laid out. now i know the inside lip of the fender(where it bolts down) is about 1"-1 1/4" tall. so i figure i can call that 25" the bottom of the fenders is chopped along with the rockers, and lower bed sides. truck only needed about 3.5" to lay the rockers, i took off another 2" to go deeper. why lay rockers when you can lay door.
bagtodrag
+1y
chop top that shit!!
time1
+1y
THE TRUCK WAS MEASURED RIGHT....I DONT KNOW WHAT ELSE TO SAY