K
WIRING HARNESS ON 20s
minimazdaon20s
+1y
WHERE IS EVERY BODY PUTTING THERE WIRING HARNESS ON THERE MAZDAS MINE IS LAID OUT ON 20s
maz2low
+1y
Edited: 9/3/2005 11:33:49 AM by Maz2low
On 20s i pulled the Harness back into the Cab Cut,Spliced,legthened and Shrink wrapped then Cut the Round hole thats on both the left and right side out of the Firewall using only one of them and Moved it to the Center of the Firewall basically so it looks factory still keeping factory Harness Grommet thing .
Then Ran it down the Frame Rail and up the Core Support looks good making no wires on the left or right side . Also right below the Washer Pump i Drilled and put a Rubber grommet in and Ran the Wire harness for that so its hidden .
Let me know if this helps
On 20s i pulled the Harness back into the Cab Cut,Spliced,legthened and Shrink wrapped then Cut the Round hole thats on both the left and right side out of the Firewall using only one of them and Moved it to the Center of the Firewall basically so it looks factory still keeping factory Harness Grommet thing .
Then Ran it down the Frame Rail and up the Core Support looks good making no wires on the left or right side . Also right below the Washer Pump i Drilled and put a Rubber grommet in and Ran the Wire harness for that so its hidden .
Let me know if this helps
maz2low
+1y
Also the old way i had it was alot cleaner but you have to take the time and do it right i Ran the Harness down the Center of the Tranny tunnel and Fished the harness through the Frame rail up to the front and since the Motor harness came from under the Tranny tunnel it hides alot of the wires on motor
balcar
+1y
Edited: 9/4/2005 7:04:13 PM by havok
if your not going to be body-dropped, you can run it between your inner fender and outer fender. The mazda I just did to lay out on 18" wheels with a 3" body drop, it worked fine. I made a hole on the flat plate that is to the left of where the stock location is, so no wires are ever seen. Hope this is understandable, i'm tired. Pics of the build on my web site. http://www.lowdowncustom.com
if your not going to be body-dropped, you can run it between your inner fender and outer fender. The mazda I just did to lay out on 18" wheels with a 3" body drop, it worked fine. I made a hole on the flat plate that is to the left of where the stock location is, so no wires are ever seen. Hope this is understandable, i'm tired. Pics of the build on my web site. http://www.lowdowncustom.com
maz2low
+1y
I figured he meant BD on 20s by saying laid out . BD on 20s it will have to be totally moved or run on the side like Maddawg on here did
balcar
+1y
not to mention other issues with clutch master cylinder and such. That is a harder issue to deal wtih than the wiring.. Just my thought.
maddawg
+1y
check out my profile there's a pic on there that shows it off to the side.
mine is draggable but i went through the harness and eliminated all the wires that were dicontinued so it's alot thinner than stock.it only consists of 14 wires.
i also have my battery cable running in the same fashon on the passenger side. i just hate all that stuff in my engine compartment.
mine is draggable but i went through the harness and eliminated all the wires that were dicontinued so it's alot thinner than stock.it only consists of 14 wires.
i also have my battery cable running in the same fashon on the passenger side. i just hate all that stuff in my engine compartment.
maddawg
+1y
here ya go.
bdroppeddak
+1y
^^^ same way i did.