K
seperating a ball joint ?
time1
+1y
Originally posted by periportfd
Originally posted by bdroppeddak
if its the upper ive always been able to separate them by hitting the spindle on the side of it with a hammer where it connects to the balljoint. if not a 2 jaw puller works fine.
Cris, what a pussy. Chuck would do it bare handed.
Bare handed?!?! What are you talking about? All he would have to do is look at it and it would fall out!
Originally posted by bdroppeddak
if its the upper ive always been able to separate them by hitting the spindle on the side of it with a hammer where it connects to the balljoint. if not a 2 jaw puller works fine.
Cris, what a pussy. Chuck would do it bare handed.
Bare handed?!?! What are you talking about? All he would have to do is look at it and it would fall out!
Low_SST
+1y
i use a BFH (big fucken hammer) and i just whack it out by beating on the control arms.
bodydropped85
+1y
put the nut back on it and whack the side of the spindle. that keeps you from boogerin the threads
dragn168
+1y
bfh is the way to go when my truck was getting bagged the kid doing it tried one of those ball joint seperators to no avail just fucked up the ball loint i went and got a BFH and two hits later things were apart
frshryd
+1y
thanks guys ! ill have another go at it on the weekend.
periportfd
+1y
Originally posted by TiMe_1
Originally posted by periportfd
Originally posted by bdroppeddak
if its the upper ive always been able to separate them by hitting the spindle on the side of it with a hammer where it connects to the balljoint. if not a 2 jaw puller works fine.
Cris, what a pussy. Chuck would do it bare handed.
Bare handed?!?! What are you talking about? All he would have to do is look at it and it would fall out!
Everyone knows if he stares at it the joint will fuse and no mortal man would be able to take it apart.
Originally posted by periportfd
Originally posted by bdroppeddak
if its the upper ive always been able to separate them by hitting the spindle on the side of it with a hammer where it connects to the balljoint. if not a 2 jaw puller works fine.
Cris, what a pussy. Chuck would do it bare handed.
Bare handed?!?! What are you talking about? All he would have to do is look at it and it would fall out!
Everyone knows if he stares at it the joint will fuse and no mortal man would be able to take it apart.
bdroppeddak
+1y
yea, chuck just pulls on that shit, either the balljoint pops out or somethin breaks. but on the real, the pickelforks do nothin but give you a headache and tore balljoint boots.
frshryd
+1y
should i hit the arm or the knuckle ?
maybe thats not the right words....ummm should i hit the piece that holds the balljoint or the arm that will come off the tapered end of the balljoint ?
maybe thats not the right words....ummm should i hit the piece that holds the balljoint or the arm that will come off the tapered end of the balljoint ?
bdroppeddak
+1y
the top of the spindle on the side where the balljoint goes through..
frshryd
+1y
k, still unsure, my balljoint is a lower one, it's upside down. it is attached to the back of the bub and there is an arm that i have to get off of it. the nut unscrews towards the ground.
when you say spindle, do you mean the tapered section of the balljoint? it looks like i should be hitting the side of the arm that i need to pop off the balljoint?
thanks for your help!
when you say spindle, do you mean the tapered section of the balljoint? it looks like i should be hitting the side of the arm that i need to pop off the balljoint?
thanks for your help!