Michigan Metal Works ---- Updates : Please Read.
66792 views
1319 replies
232 following
K
Michigan Metal Works ---- Updates : Please Read.
tuckinlugs06
+1y
big you bringing the billets to scrapin this year
thacru78
+1y
What staff shirt!!! Lol. That thing came in handy Saturday night. Lol. No cruising sir....where are you going...oh nevermind your staff. Hahaha. Good times...I'll be at Scrapin...not sure what will be with me :secret: lol
jeebus @ mmw
+1y
Had to snap a sneak preview of this upper arm im working on. Its made to bend around a stock steering shaft on a C10 truck. It will clear up to a 33" OD tire... yea a 305-35-24, for any idiot wanting to give themselves a headache lol, me included.
It bends around the stock steering shaft, and clears every part of it through its entire travel cycle. I would love to see someone construct this arm with tubing, and make that work. My first thought was to bend a piece of tube down so it would clear the steering shaft when layed out..... but...... then your limited to 7" of vertical lift, because that bent piece of tube hits your spring bucket.... not enough to un tuck rim let alone tire, i tried to make sure. These arms were nearly my first tube arms in a long time untill that problem arose.
Anyways, i kinda think they look cool as well...
It bends around the stock steering shaft, and clears every part of it through its entire travel cycle. I would love to see someone construct this arm with tubing, and make that work. My first thought was to bend a piece of tube down so it would clear the steering shaft when layed out..... but...... then your limited to 7" of vertical lift, because that bent piece of tube hits your spring bucket.... not enough to un tuck rim let alone tire, i tried to make sure. These arms were nearly my first tube arms in a long time untill that problem arose.
Anyways, i kinda think they look cool as well...
thacru78
+1y
That's wicked. Tube arms are overrated. I like the flat plate alot more. Can't wait to see these installed.
zaccanti
+1y
If these are goin were i think they are, itdontstop.......... arms are bitchen, i should be gettin at you sooner then later on mine lol keep up the good work bro
jeebus @ mmw
+1y
Na, those arms are for my personal truck. I installd them last night, they work great!
Taylor
Taylor
needekhatch
+1y
Hey I know u sell s10 arms what size tire will they lay on with stock spindles and with drop spindles
Also do they help move the wheel forward to center the wheel up
If not could u do that build a set to move the wheel forward like an inch
What would the cost b on something like that regular lower ball joints upper jeebus joints billet cross shafts and move the wheel forward
With powder coat and the no notch tierod ends
Also do they help move the wheel forward to center the wheel up
If not could u do that build a set to move the wheel forward like an inch
What would the cost b on something like that regular lower ball joints upper jeebus joints billet cross shafts and move the wheel forward
With powder coat and the no notch tierod ends
jeebus @ mmw
+1y
Shoot me an email at info@michiganmetalworks.com
There are a lot of options there to go through, i will give you all the details and options of what you can use with stock spindles and drop spindles, as well as jeebus joint and ball joint options.
Taylor
There are a lot of options there to go through, i will give you all the details and options of what you can use with stock spindles and drop spindles, as well as jeebus joint and ball joint options.
Taylor
jeebus @ mmw
+1y
New set of Budget C-10 Arms. These are designed to be used with stock style bolt in ball joints, and stock x-shafts. They can be lengthened or narrowed any amount at no extra charge, and only run 149$ per pair with free powder coat!
slimneverdies
+1y
I think I know who those belong to. I can't wait