K
Slammed
societyoutkast
+1y
i agree with fester
societyoutkast
+1y
hey what does the inside of the bed look like
Cruz Lo
+1y
Thanks again "everyone" for the comments.
Originally posted by GMracer
Looks absolutely stunning man, one question what are the specs on the wheels... width narrowed rear end? back spacing, Im assuming the frame is narrower back there, so the 4link bars don't get in the way with the ebrake? Awesome build!
My E Brake is the Truck on the ground!It was removed. No room for the stock one with the Firewall mods. The Rear End was shortened 10 inches total. I got the MIN backspace Intro would give me.
The rear brakes were flipped to the back to give max width for the frame. And room for the four bar etc..
Originally posted by GMracer
Looks absolutely stunning man, one question what are the specs on the wheels... width narrowed rear end? back spacing, Im assuming the frame is narrower back there, so the 4link bars don't get in the way with the ebrake? Awesome build!
My E Brake is the Truck on the ground!It was removed. No room for the stock one with the Firewall mods. The Rear End was shortened 10 inches total. I got the MIN backspace Intro would give me.
The rear brakes were flipped to the back to give max width for the frame. And room for the four bar etc..
Cruz Lo
+1y
Originally posted by society_outkast
hey what does the inside of the bed look like
OK But remenber what I said in the first post!
hey what does the inside of the bed look like
OK But remenber what I said in the first post!
///DragBdy
+1y
the attention to detail is amazing!
icstarz
+1y
beautiful
BaggedMazda87
+1y
I'm gonna go kill myself
Holy balls brotha, hats off to you.
The work is amazing.
And when I see that you made everything with simple hand tools-mind blowing.
Much props to you.
Holy balls brotha, hats off to you.
The work is amazing.
And when I see that you made everything with simple hand tools-mind blowing.
Much props to you.
Cruz Lo
+1y
Edited: 1/31/2008 1:55:22 PM by Cruz Lo
Thanks;
Oh sh** Tyler don't kill yourself man. LOL
Yes. Eveything was cut by hand with hand tools, except some of the rear parts that a machine shop had to turn/broach to my design. And the parts I out sourced.
everyone knows it's hard to get everything to work together right.
I made full size models to make the front, rear, canti, and watts link work the best I could figure out.
Below is my advanced suspension design tool (HAHA) used in this case to determine the behavior of the Watts link with different length bars, and crank position.
Ya I know it sounds geeky but hey, I hated math in school now I use geometry and trig eveytime I have to figure a sub box volume!!
Its hard to see but each tape shows a different line (shifting up to 1/2 inch side to side) I kept it up until I got the best results over 15 inches of travel.
Thanks;
Oh sh** Tyler don't kill yourself man. LOL
Yes. Eveything was cut by hand with hand tools, except some of the rear parts that a machine shop had to turn/broach to my design. And the parts I out sourced.
everyone knows it's hard to get everything to work together right.
I made full size models to make the front, rear, canti, and watts link work the best I could figure out.
Below is my advanced suspension design tool (HAHA) used in this case to determine the behavior of the Watts link with different length bars, and crank position.
Ya I know it sounds geeky but hey, I hated math in school now I use geometry and trig eveytime I have to figure a sub box volume!!
Its hard to see but each tape shows a different line (shifting up to 1/2 inch side to side) I kept it up until I got the best results over 15 inches of travel.
oh4sho
+1y
Truly inspiring man. So did you say you are not entering this in cavalcade.
SuicidalCustomz
+1y
hey man the truck is Fu*kn sick bro!! if you dont mind me asking how much did you shorten your rear?? and whats the offset on those wheels the lip in the rear is deeeep i like it alot!